Maritime Glossary

Searchable A-Z glossary of maritime, shipbuilding, marine engineering, quality and inspection terminology.

A

AISNavigation & Seamanship

Automatic Identification System: a VHF transponder system exchanging identity, position, course and speed between ships and shore stations.

AnchorageNavigation & Seamanship

A designated area where vessels may lie at anchor, with suitable depth, holding ground and shelter.

AntifoulingMarine Materials & Metallurgy

A coating applied to the underwater hull to prevent the attachment of marine organisms, which increase resistance and fuel consumption.

Auxiliary EngineMarine Machinery & Propulsion

An engine that does not drive the propeller directly, most commonly driving a generator to supply electrical power.

B

BallastMarine Engineering Terminology

Weight, normally sea water in dedicated tanks, carried to adjust draft, trim, heel and stability.

BerthPorts & Terminal Operations

A designated place where a vessel is moored, at a quay, pier or jetty. The term also covers the allocated length of quay and depth of water for one ship.

BilgeMarine Engineering Terminology

The lowest internal part of the hull where water collects, and the rounded transition between bottom and side. Bilge systems pump this water out.

Bill of LadingMarine Supply Chain & Procurement

A document issued by the carrier acknowledging receipt of cargo for shipment, evidencing the contract of carriage and serving as a document of title.

Block AssemblyShipbuilding Terminology

The construction of a hull in large prefabricated sections (blocks) that are built in workshops, often pre-outfitted, and then erected and welded together on the berth.

BollardPorts & Terminal Operations

A short, strong post on a quay or on a vessel's deck to which mooring lines are made fast. Deck bollards are also called bitts.

Bollard PullInspection & Testing

The static pulling force a vessel can exert on a fixed bollard, the key performance figure for tugs and anchor handlers.

BulkheadShip Structures & Hull Terminology

A vertical partition dividing the hull into compartments. Watertight bulkheads limit flooding; fire-rated bulkheads limit the spread of fire; structural bulkheads contribute to hull strength.

BulwarkShip Structures & Hull Terminology

The plating extending above the weather deck at the ship's side, protecting people and deck cargo from the sea.

C

CAPAQuality Assurance & Quality Control

Corrective and Preventive Action: the process of eliminating the cause of a detected non-conformity and preventing occurrence of potential ones.

CapstanMarine Engineering Terminology

A vertical-axis rotating drum used for heaving mooring lines.

Cathodic ProtectionMarine Materials & Metallurgy

Corrosion protection of immersed metal by making it the cathode of an electrochemical cell, using sacrificial anodes or an impressed current system.

Class SurveyMarine Classification & Compliance

A periodical or occasional survey by the classification society to maintain class: annual, intermediate, special (renewal) and docking surveys.

Classification SocietyMarine Classification & Compliance

An independent organisation that sets technical rules for the design and construction of ships, verifies compliance by plan approval and survey, and maintains class through periodical surveys.

CommissioningInspection & Testing

The controlled process of bringing installed equipment and systems into operation and verifying they function as designed.

CouplingMarine Machinery & Propulsion

A component connecting two shafts to transmit torque. Flexible couplings absorb misalignment and torsional vibration; rigid flange couplings do not.

D

DavitMarine Safety

A crane-like device for lowering and recovering lifeboats, rescue boats or tenders.

DeadweightMaritime Terminology

The carrying capacity of a ship in tonnes: the difference between loaded displacement and lightship weight. It includes cargo, fuel, water, stores and crew.

DeckShip Structures & Hull Terminology

A horizontal structural platform in a vessel. The freeboard deck and strength deck have specific meanings in load line and structural rules.

DisplacementMaritime Terminology

The weight of water displaced by a floating vessel, equal to the vessel's total weight. Light displacement is the ship alone; loaded displacement includes everything on board.

DockPorts & Terminal Operations

An enclosed or partly enclosed area of water where vessels lie for cargo operations or repair. In American usage the word also refers to the quay or pier itself.

Double BottomShip Structures & Hull Terminology

A hull bottom built with an inner and outer skin, forming tanks for ballast, fuel or fresh water and protecting against grounding damage.

DraftMaritime Terminology

The vertical distance from the waterline to the lowest point of the hull, also spelled draught. It is read from draft marks at bow, stern and midships.

Dry DockShip Repair & Maintenance

A basin that can be closed by a gate and pumped dry so that a vessel rests on keel blocks, exposing the underwater hull for inspection, repair and coating. Also called a graving dock.

Duplex Stainless SteelMarine Materials & Metallurgy

Stainless steel with a mixed austenitic-ferritic microstructure, combining higher strength with good resistance to chloride stress corrosion and pitting.

Dynamic PositioningOffshore Engineering

A computer-controlled system that automatically maintains a vessel's position and heading using its own thrusters. Equipment classes 1 to 3 define redundancy.

E

ECDISNavigation & Seamanship

Electronic Chart Display and Information System: a type-approved navigation system displaying electronic navigational charts with the ship's position.

Emergency GeneratorMarine Electrical & Automation

An independent generator located outside the main machinery space that automatically supplies essential services if the main source fails.

EPIRBMarine Safety

Emergency Position Indicating Radio Beacon: a float-free beacon that transmits a distress alert with the vessel's identity via satellite.

ExpeditingMarine Supply Chain & Procurement

Systematic follow-up of a purchase order to secure delivery on the required date, by monitoring and influencing progress at supplier and sub-suppliers.

F

FAIQuality Assurance & Quality Control

First Article Inspection: complete verification of the first part produced by a new or changed process against all drawing requirements.

FairingYacht Construction Terminology

Applying and sanding filler on a yacht hull and superstructure to obtain a smooth, fair surface before the paint system.

FairwayNavigation & Seamanship

The navigable channel in a harbour, river or approach, normally marked by buoys and maintained at a charted depth.

FATInspection & Testing

Factory Acceptance Test: tests performed at the manufacturer's works to demonstrate that equipment meets its specification before shipment.

FenderPorts & Terminal Operations

An energy-absorbing element, usually rubber or foam, placed between a vessel and a quay or between two vessels to prevent damage.

Fire DamperMarine Safety

A closing device in a ventilation duct that prevents the passage of fire and smoke through a fire-rated division.

Flag StateMarine Classification & Compliance

The state whose flag a ship flies and under whose laws it is registered. The flag administration enforces international conventions, often delegating surveys to recognised organisations.

FlangeMarine Engineering Terminology

A rim on a pipe, valve or fitting that allows a bolted, gasketed joint. Dimensions and pressure ratings follow standards such as EN 1092-1, ASME B16.5 or JIS.

Floating DockShip Repair & Maintenance

A submersible pontoon structure with side walls that is ballasted down to receive a vessel and then deballasted to lift it clear of the water.

FrameShip Structures & Hull Terminology

A transverse stiffening member of the hull, comparable to a rib, supporting the shell plating. Frame numbers are the standard position reference on board.

FreeboardMaritime Terminology

The vertical distance from the waterline to the upper edge of the freeboard deck at the side, amidships. Minimum freeboard is assigned under the Load Line Convention.

G

Galvanic CorrosionMarine Materials & Metallurgy

Accelerated corrosion of the less noble metal when two different metals are in electrical contact in an electrolyte such as sea water.

GangwayMaritime Terminology

A portable bridge or ladder giving access between ship and shore, or an opening in the ship's side for the same purpose.

GearboxMarine Machinery & Propulsion

A unit that reduces engine speed to propeller speed and may include clutches and reversing gear.

Gel CoatYacht Construction Terminology

The pigmented resin layer applied first into a mould, forming the outer surface of a composite moulding.

GensetMarine Electrical & Automation

A generator set: an engine coupled to an alternator on a common base frame, with its control and protection equipment.

GMDSSNavigation & Seamanship

Global Maritime Distress and Safety System: the internationally agreed set of radio equipment and procedures for distress alerting and safety communication.

GovernorMarine Machinery & Propulsion

A device that controls engine speed by regulating fuel supply in response to load changes. Modern governors are electronic.

Gross TonnageMaritime Terminology

A dimensionless index of a ship's total enclosed volume, calculated under the 1969 Tonnage Convention. It is not a weight.

GRP LaminationYacht Construction Terminology

Building up a glass-reinforced plastic structure from layers of fibre reinforcement and resin, by hand lay-up, vacuum infusion or prepreg.

H

HATInspection & Testing

Harbour Acceptance Test: tests of installed equipment and systems carried out with the vessel alongside, before sea trials.

Heat ExchangerMarine Engineering Terminology

Equipment transferring heat between two fluids without mixing them. Plate and shell-and-tube types are common for cooling engines and oil.

Hold PointQuality Assurance & Quality Control

A stage in the ITP beyond which work must not proceed without the attendance or written release of the designated party.

HullShip Structures & Hull Terminology

The watertight body of a vessel, comprising bottom, sides and decks with their internal stiffening, excluding superstructure, machinery and outfit.

Hydraulic Power UnitMarine Engineering Terminology

A packaged unit with tank, pumps, motor, valves, filters and coolers supplying pressurised hydraulic fluid to actuators. Abbreviated HPU.

Hydrostatic TestInspection & Testing

A pressure test using water, in which a component or system is pressurised above its working pressure and held to prove strength and tightness.

I

Inclining TestInspection & Testing

A test in which known weights are moved across the deck of the nearly completed vessel and the resulting heel is measured, to determine lightship weight and vertical centre of gravity.

IncotermsMarine Supply Chain & Procurement

Standard trade terms published by the International Chamber of Commerce defining the division of costs, risks and tasks between seller and buyer, such as EXW, FCA, FOB and DAP.

Insulation Resistance TestInspection & Testing

Measurement of the resistance of electrical insulation by applying a DC test voltage between conductors and earth, commonly called a megger test.

IP RatingMarine Electrical & Automation

Ingress protection code (IEC 60529) describing an enclosure's protection against solid objects and water, written as IP followed by two digits.

ITPQuality Assurance & Quality Control

Inspection and Test Plan: a table listing each inspection and test in the manufacturing sequence with its reference document, acceptance criteria, record and the attendance of each party.

J

Jack-upOffshore Engineering

A self-elevating unit with legs that are lowered to the seabed so the hull can be raised clear of the water.

JettyPorts & Terminal Operations

A structure projecting into the water, used either for berthing, typically tankers at an oil or gas jetty, or to protect a harbour entrance and influence currents.

K

KeelShip Structures & Hull Terminology

The principal longitudinal structural member along the bottom centreline of a hull. Keel laying is the traditional formal start of construction.

L

LashingMarine Supply Chain & Procurement

Securing cargo with chains, wires, straps and fittings so that it cannot move during transport.

LaunchingShipbuilding Terminology

The transfer of a newly built hull from the building berth into the water. It marks the end of the main structural phase and the start of afloat outfitting.

LifeboatMarine Safety

A rigid survival craft carried for abandoning ship, launched by davits or by free-fall.

LiferaftMarine Safety

An inflatable survival craft stowed in a container and released manually or by a hydrostatic release unit.

LightshipMaritime Terminology

The weight of the vessel complete and ready for service but without cargo, fuel, stores, ballast, crew or passengers.

Load Bank TestInspection & Testing

A test in which a generator is loaded with a resistive or reactive load bank to prove its rated output and behaviour under load.

M

Magnetic Particle TestingInspection & Testing

An NDT method for ferromagnetic materials: the part is magnetised and fine iron particles gather at surface and near-surface discontinuities.

Main EngineMarine Machinery & Propulsion

The prime mover that drives the propulsion system, usually a diesel or dual-fuel engine, or the generators in a diesel-electric arrangement.

ManifoldMarine Engineering Terminology

A pipe or block with several inlets or outlets that distributes or collects flow, such as a cargo manifold or a hydraulic manifold block.

MARPOLMarine Classification & Compliance

The International Convention for the Prevention of Pollution from Ships, covering oil, chemicals, sewage, garbage and air emissions in its annexes.

Mill CertificateMarine Materials & Metallurgy

A document from the material manufacturer stating chemical composition and mechanical properties for a specific heat or batch. EN 10204 type 3.1 is validated by the manufacturer's independent inspection representative; type 3.2 additionally by a third party or the purchaser's representative.

MoonpoolOffshore Engineering

A vertical opening through the hull giving sheltered access to the sea for drilling, diving or subsea equipment handling.

MooringMaritime Terminology

Securing a vessel to a quay, buoy or another vessel with lines, or the equipment and arrangement used to do so.

N

NCRQuality Assurance & Quality Control

Non-Conformance Report: a formal record of a product or process that does not meet a specified requirement, with its disposition.

NDTInspection & Testing

Non-Destructive Testing: methods of examining materials and welds for defects without damaging them, including visual, penetrant, magnetic particle, ultrasonic and radiographic testing.

O

OutfittingShipbuilding Terminology

All work that turns a bare hull into a working vessel: installation of machinery, piping, electrical systems, deck equipment, insulation and accommodation.

P

Penetrant TestingInspection & Testing

A surface NDT method in which a coloured or fluorescent liquid is drawn into surface-breaking defects and made visible by a developer.

PierPorts & Terminal Operations

A structure projecting from the shore into the water, allowing vessels to berth on one or both sides.

PLCMarine Electrical & Automation

Programmable logic controller: an industrial computer that controls machinery and processes through inputs, outputs and a stored program.

PQRWelding & Fabrication

Procedure Qualification Record: the record of a test weld and its mechanical test results that qualifies a welding procedure. Called WPQR in ISO 15614.

Pre-Shipment InspectionMarine Supply Chain & Procurement

An inspection of goods before dispatch to confirm quantity, specification, marking and packing against the order.

PropellerMarine Machinery & Propulsion

A rotating hub with blades that converts shaft torque into thrust. Fixed-pitch and controllable-pitch are the main types.

PumpMarine Engineering Terminology

A machine that moves liquid by adding energy to it. Centrifugal pumps are used for high flow; positive displacement pumps for viscous fluids and high pressure.

Punch ListQuality Assurance & Quality Control

A list of outstanding defects and incomplete items identified at an inspection or test, each to be corrected and closed before acceptance.

Q

QuayPorts & Terminal Operations

A solid structure built parallel to the shoreline, alongside which vessels berth to load, discharge, lie for outfitting or undergo repair. A quay has a vertical face, a paved apron and is fitted with bollards and fenders.

R

RadarNavigation & Seamanship

A navigation system that detects objects and measures their range and bearing using reflected radio waves. Marine radars operate in X-band and S-band.

Radiographic TestingInspection & Testing

A volumetric NDT method using X-rays or gamma rays to produce an image of a weld or casting, showing internal defects.

RefitShip Repair & Maintenance

A planned period of repair, renewal and modification work on an existing vessel or yacht, more extensive than routine maintenance.

RudderMarine Machinery & Propulsion

A movable control surface at the stern, turned by the steering gear, that steers the vessel by deflecting water flow.

S

SATInspection & Testing

Sea Acceptance Test: tests at sea demonstrating system performance under operating conditions. In industry generally SAT also means site acceptance test.

ScupperMarine Engineering Terminology

A drain opening that leads water from a deck overboard or to a drainage system.

Sea ChestMarine Engineering Terminology

A recess in the underwater hull, fitted with a grating, from which sea water is drawn for cooling, ballast and fire-fighting systems.

Sea TrialInspection & Testing

The programme of tests carried out at sea before delivery to verify speed, manoeuvrability, machinery performance and equipment function.

Shaft AlignmentInspection & Testing

The process of positioning shaft bearings and the engine or gearbox so that bearing loads and shaft stresses stay within limits in all operating conditions.

Shaft LineMarine Machinery & Propulsion

The assembly transmitting power from engine or gearbox to the propeller: intermediate shafts, propeller shaft, bearings and couplings.

Shell PlatingShip Structures & Hull Terminology

The plates forming the outer skin of the hull, arranged in longitudinal rows called strakes.

Shore PowerMarine Electrical & Automation

Electrical supply from the quay to a vessel in port, allowing generators to be stopped. Also called cold ironing or onshore power supply.

SlipwayShipbuilding Terminology

An inclined surface running into the water on which vessels are built or hauled out. Launching may be longitudinal or sideways.

SOLASMarine Classification & Compliance

The International Convention for the Safety of Life at Sea: the principal IMO treaty on ship construction, equipment and operation for safety.

StabiliserYacht Construction Terminology

A system reducing roll motion, using fins, gyroscopes or tanks. Zero-speed fin stabilisers work at anchor.

Stern TubeMarine Machinery & Propulsion

The tube through the stern structure that carries the propeller shaft, its bearings and seals, keeping sea water out and lubricant in.

StringerShip Structures & Hull Terminology

A longitudinal stiffening member running along the side shell or deck, supporting frames and plating.

SuperstructureShip Structures & Hull Terminology

A decked structure above the freeboard deck extending from side to side of the ship, or nearly so. Narrower structures are deckhouses.

SwitchboardMarine Electrical & Automation

An assembly of switching, protection and measuring equipment that receives and distributes electrical power. The main switchboard is fed by the generators.

T

ThrusterMarine Machinery & Propulsion

A propulsion unit producing transverse or steerable thrust. Tunnel thrusters assist manoeuvring; azimuth thrusters provide main propulsion and steering.

TraceabilityQuality Assurance & Quality Control

The ability to follow the history of a material or part through records, from the mill heat number to the finished, installed component.

TrimMaritime Terminology

The difference between the draft forward and the draft aft. A vessel deeper aft is trimmed by the stern.

Type ApprovalMarine Classification & Compliance

Certification by a classification society or administration that a product design meets defined standards, allowing series production under agreed conditions.

U

Ultrasonic TestingInspection & Testing

A volumetric NDT method using high-frequency sound waves; reflections reveal internal defects and allow thickness measurement.

V

ValveMarine Engineering Terminology

A device that starts, stops, regulates or directs flow in a pipe. Gate, globe, butterfly, ball and check valves are the main marine types.

VFDMarine Electrical & Automation

Variable frequency drive: power electronics that control the speed and torque of an AC motor by varying supply frequency and voltage.

Visual TestingInspection & Testing

Examination of a surface or weld by eye, with aids such as gauges, lighting and magnification. It is the first NDT method applied.

W

Welder QualificationWelding & Fabrication

Certification that a welder has made a satisfactory test weld under defined conditions, for example to ISO 9606 or class rules.

WharfPorts & Terminal Operations

A structure along the waterfront for berthing vessels, often built on piles so that water flows beneath it. In everyday use it overlaps with quay; a quay is normally a solid, filled structure.

WindlassMarine Engineering Terminology

A deck machine for hoisting and lowering the anchor and chain, with a chain wheel (gypsy) and brake.

Witness PointQuality Assurance & Quality Control

A stage in the ITP where the designated party is notified and may attend; work may proceed if they do not attend after proper notice.

WPSWelding & Fabrication

Welding Procedure Specification: the document giving the welder the variables for a specific joint, process, material, consumable, position, preheat and parameters.